Home   |   About Us   |   Products   |   Services   |   Technology   |   Site Map   |   Contact Us
Bearing Housings
STAMPED HOUSINGS
    flanges   FLANGES
    pillow block set   PILLOW BLOCK SETS
    pillow block stands   PILLOW BLOCK STANDS
    flush mounts   FLUSH MOUNTS
    take-up units   TAKE-UP UNITS
    custom bearings   PARTS MADE TO YOUR PRINTS
    BRONZE BUSHED BEARING ASSEMBLIES
    pillow blocks   PILLOW BLOCKS
    flange side mounts   FLANGE SIDE MOUNTS
    flange mounted   FLANGE MOUNTED
    NEW PRODUCTS
    plastic bearings   PLASTIC BEARINGS
    SPECIAL PRODUCTS
    rubber boots   RUBBER BOOTS
    bronze bushed bearings   BRONZE BUSHINGS &
BRONZE THRUST WASHERS
    bronze bar stock   BRONZE BAR STOCK
         

Two-Bolt Flush Mounts (Rubber Booted)

Flush mounted zinc plated pressed steel two-bolt units including static conductive rubber boots for noise and vibration reduction.   Needs no frame opening.   Designed for standard ball bearings with cylindrical OD of 40MM, 47MM, and 52MM.   Covers all standard shaft sizes from ½" thru 1".   Choose proper unit number for your application from chart below.   Includes stamped housing and rubber boot only.   Remember, Manitou doesn't carry ball bearings.

rubber booted flush mount
UNIT No. (Each unit includes: 1 Stamped Housing & 1 Rubber Boot.) Shaft
Size 		Dimensions (in.)
Rubber Boot No. 		Stamped Housing No.
A B C D
 E F G H
728-2-MFM 1/2, 5/8, 9/16, 11/16 4 3 2 .451 3/4 1.5748 (40MM) 5/8 16 GA. R-728 SH-728-2
729-2-MFM 3/4 4- 1/2 3- 3/8 2- 1/2 .451 3/4 1.8504 (47MM) 3/4 16 GA. R-729 SH-730-2
730-2-MFM 3/16, 7/8, 15/16, 1 4- 1/2 3- 3/8 2- 1/2 .451 3/4 2.0472 (52MM) 3/4 16 GA. R-730 SH-730-2
NEW!! Flush Mounts
New low cost Flush Mounts for your standard ball bearings with cylindrical OD require no frame opening. MFM units have same bolt spacing as corresponding standard flanges.
Part No. Shaft
Size 		Dimensions (in.)
A B C D
 E F G H I
40-2-MFM 1/2, 9/16, 5/8 3-3/16 2-1/2 2-5/16 9/32 Square 9/32 Square 1.5748 (40 MM) .512 .074 1.25
47-2-MFM 3/4 3-9/16 2-13/16 2-5/8 11/32 Square 11/32 Square 1.8504 (47 MM) .590 .074 1.428
52-2-MFM 3/16, 7/8, 15/16, 1 3-3/4 3 2-51/64 11/32 Square 11/32 Square 2.0472 (52 MM) .590 .074 1.625
52-2-CFM 3/16, 7/8, 15/16, 1 4-1/8 3-1/4 2-1/4 7/16 Round 7/16 Round 2.0472 (52 MM) .590 .062 1.906
62-2-MFM 1-1/16, 1-1/8, 1-13/16, 1-1/4 4-7/16 3-9/16 3-1/4 13/32 Square 13/32 Square 2.4409 (62 MM) .709 .089 2.018
Part No. Shaft
Size 		Dimensions (in.)
A B C D
 E F H I
40-3-MFM 1/2, 9/16, 5/8 3-3/16 2-1/2 9/32 9/32 .512 1.5748 (40 MM) .074 1.153
47-3-MFM 3/4 3-9/16 2-13/16 11/32 11/32 .590 1.8504 (47 MM) .074 1.428
52-3-MFM 3/16, 7/8, 15/16, 1 3-3/4 3 11/32 11/32 .590 2.0472 (52 MM) .074 1.625
62-3-CFM 1-1/16, 1-1/8, 1-13/16, 1-1/4 4-7/16 3-9/16 13/32 13/32 .709 2.4409 (62 MM) .089 2.018
52-4-MFM 3/16, 7/8, 15/16, 1 3-5/8 2-61/64 .2756 Round Holes 4 Holes 15.5 MM 2.0472 (52 MM) .0787 1.378
P.O. Box 10526 • White Bear Lake, MN 55110-0526 • Tel: 651-429-4285 • 1- 800-894-1509 • Fax: 651-429-5765 • Email: info@manitoumfg.com